Since its release in 2013, the Syma X5C drone has become a favorite among quadcopter enthusiasts. And for a good reason. It is famously cheap, easy to use, and reliable for a drone that costs less than $100.
As is to be expected, what goes up must come down – there is a lot of wear involved. Luckily, most parts can be replaced easily with bought components. But makers have a few aces up their sleeves too. Check out the impressive Syma X5C spare parts you can 3D print!
Obviously, weight is everything when it comes to drones. Simply consider that Syma X5C in full configuration has a flying time of up to 5 minutes. Take off the camera, legs and propeller guards, and you get a flying time of some 9 minutes. Also, the aerodynamic properties improve the less weight the drone carries. It flies steadier, is less susceptible to wind, and, most importantly, it speeds up faster! What is the lesson to be learned? Go easy on the infill. To balance weight and durability is ultimately a learning process.
You don’t have a 3D printer to call your own? Try All3DP’s Online 3D Printing Price Comparison for the best quotes. Oh, and for your information: If you choose to buy an item through this article, we get a small commission to keep up our work.
To learn more about 3D printing parts for drones read our article on 3D printed drones in general:
AVAWO Spare Parts Kit
What is this Syma X5C Quadcopter accessory? In case you are a frequent flyer, you should consider getting this handy spare parts kit by AVAWO. It has spares for all the parts that quickly wear on the Syma X5C Quadcopter: Body Shell, 4 Plastic Motor Base, 16 Spare Blades Set, 4 motors, 2 600mAh batteries, 8 gears, 2 LED lights, 4 LED covers, 1 landing skid, and 4 propeller guards. Also, the parts are compatible with Syma X5, X5C, and X5C-1.
Keenstone 720mAh Battery
What is this Syma X5C Quadcopter accessory? Do you want to extend the flight time of your Syma X5C quadcopter? But stripping it off the camera or other parts is not an option? Replace the original 500mAh battery with this pack of 6 lightweight 720mAh batteries. The set even includes a charger that protects against overcharging. What is more, the batteries are compatible with the Syma X5, X5C, X5SC, and X5SW quadcopters.
Coolplay Receiver Board
What is this Syma X5C Quadcopter accessory? Even though the receiver board is well protected in the body of your Syma X5C Quadcopter, it may break when crash-landing. With this spare receiver, your drone will be back in the air in no time. To build it into the body you will have to solder. To spare yourself much grief take a photo of the old board to remember the way the leads are connected to it.
Coolplay HD Camera Set
What is this Syma X5C Quadcopter accessory? Mounted on the bottom of the Syma X5C quadcopter, the HD camera is particularly in danger to get damaged in collisions or crashes. In the event replace it with this 2.0 MP camera by Coolplay. The pack includes 4GB SD card and a card reader. Like the original, it may not give you cinema-grade results, but half the fun of drones are the images and films you make.
Greenco Carrying Case
What is this Syma X5C Quadcopter accessory? When you go outside to fly your drone, carrying it in cardboard boxes and other makeshift transportation containers will not cut it. Since fragile parts like propellers and their guards break easily. Protect your equipment with this robust carrying case. Also, it will keep your Syma X5C quadcopter accessories organized. The carrying case has pre-cut slots for the drone, the RC, up to 4 batteries, spare rotors, charger, and there is even a small slot for an SD Card reader.
Feet
What is this Syma X5C Quadcopter accessory? Add more lateral stability to your Syma X5C with these nifty replacement feet. Also, they give the camera mounted at the bottom some measure of protection. The designer estimates that the approximate weight will be 3.6 grams if you 3D print this Syma X5C quadcopter accessory from ABS filament. It´s made by Chris Wier.
Propeller Guard
What is this Syma X5C Quadcopter accessory? Propeller guards are probably the single most Syma X5C quadcopter accessories susceptible to breaking on your next flight. Why buy a whole pack of replacements when you can 3D print one in case you need it? According to the designer, 1mm is the ideal height for the guards. Prints without supports at a layer-height of 0.2mm at 50 mm/s. It´s made by Goofy34.
Drone Racer Frame
What is this Syma X5C Quadcopter accessory? This Drone Racer body for the Syma X5C quadcopter will improve its speed and aerodynamic capabilities. Don’t you believe us? Just watch this video. Basically, you gut your quadcopter of its mechanical and electrical components and build them into the new body. The 3D printed quadcopter frame weighs 102 grams, which is identical to the original. Take note that this frame requires soldering some wires. It´s made by didier didier.
Wall Hook
What is this Syma X5C Quadcopter accessory? Do you have more than one drone? Tidy up your Syma X5C quadcopter and controller. 3D print this simple, yet ingenious wall hook. This design is quite undemanding, as it requires no rafts or supports. According to the designer, a resolution of 0.3mm and infill of 50% are expedient for a smooth surface and durability. It´s made by dionlevi.
Antenna Mod
What is this Syma X5C Quadcopter accessory? Many Syma X5C quadcopter users report that their range already exceeds the 50 meters promised by the manufacturer. If you want to push the boundaries even further consider this modification of the controller antenna. You solder a 5/4wave 2.4GHz wire antenna and encase it in this 3D printed shell. The design 3D prints without rafts or supports at a resolution of 0.35mm. It´s made by Chris Harrison.
Disclaimer:
All3DP GmbH makes 3D printing available to everyone.
If you choose to buy an item through one of All3DP’s articles, we do not charge any fee or additional price on top of our partners fulfillment price. We are paid on a commission, which means that we receive a small percentage from our partners.
Also, we are not selling the models. By comparing the prices of our 3D printing services, we simply are pointing you to the lowest 3D printing price available. If you would like to know more, please visit our Terms of Service.
Also, the editorial team of All3DP only conveys models that are under Creative Commons 4.0 Licence. All3DP will never convey STL files which are marked with the non-commercial use licence (CC NC). Also, according to CC BY, we give attribution where needed. If you are the designer of a model and want to be removed from All3DP’s price comparison service, please send a mail to contact@all3dp.com.
License: The text of "10 Best Syma X5C Quadcopter Accessories to Buy or DIY" by All3DP is licensed under a Creative Commons Attribution 4.0 International License.